ALLEN & HEATH XONE:02 DJ MIXER
Stereo pro-turntablist DJ mixer
From inputs to outputs, we created Xone2:02 to be the world’s greatest battle / scratch mixer. The crossfader is a deluxe Penny & Giles VCA design, reversible, they all have contour controls and they can all be easily replaced by removing the steel faceplate. We’ve kept the fader area clear for action and we’ve kept controls like pan and EQ out of the way on low profile sliders. Even the transform switches can be rotated to work the way you like them. Don’t go into battle with anything less.
-3 filter types (High Pass, Band Pass and Low Pass)
-Resonance- which controls the sharpness of the filter
-Envelope follower and a wide range LFO
-MIDI can be sent and received allowing the filter to be remotly controlled
-Filter can be run as a stereo 2-pole (12dB/octave) or a mono 4-pole (24dB/octave)
| 2 Dual Stereo Channels |
| Channels have RIAA [RCA] inputs, switchable to line, plus stereo line level inputs [RCA], each with gain control. Powerful 3 band ‘music’ EQ on sliders. High quality 45mm faders. Input reverse switch for battle mixing. Pre fade monitoring on 12 segment 3 colour peak reading bar meters |
| Mic Channel |
| 2 XLR inputs with separate gain controls, on switch and 3 band EQ with HPF. Routes direct to mix outputs. FX insert on button |
| Stereo Mix Outputs |
| Balanced mix outputs on XLR with multi-point VCA level master control. The mix output level can be displayed on the 12 segment 3 colour peak reading bar meters |
| Booth Output |
| RCA outputs with level control for booth / link out to additional ‘daisy-chain’ mixers |
| FX Loop |
| Channels have an effect loop on switch with silent FET switching. Effect insert points are separate [TRS] inputs and outputs |
| 3 Band EQ |
| Powerful 3 band 12dB/oct EQ with ëasymmetricí characteristic: +6dB boost emphasis and -26dB cut for frequency band elimination |
| VCA Faders |
| High quality dual-rail, gold-contact, conductive plastic 45mm faders with contour control, reverse switch and led. Crossfaders can be upgraded to ultra-high quality Penny & Giles conductive plastic faders, and can be substituted in minutes by removing the faceplate |
| Transform Switches |
| Performance channel mute controls which can be rotated to work up/down or left / right |
| Engineer / DJ’s Toolbox |
| High powered headphone output with level and mute switch. Booth / link output on TRS with level. 12 segment 3 colour bar metering displays CH1&2 or mix. Channels have 12 segment 3 colour bar meters. CH1 / CH2 cue fader allows preview of x-fades |
| PSU |
| High performance internal switched-mode power supply. Universal mains input voltage |
| INPUTS | |||
| Turntable | RCA | RIAA Equalisation (Switch-able to line) | 2-140mV 47K/330pF |
| Line | RCA | >8k2 ohms | -15 / +22 dBu |
| Effect Return | TRS jack | 10k ohms | 0dBu |
| Link IN | RCA | 10k ohms | 0dBu |
| MIC | XLR | <2k ohms Balanced | -10 / -50dBu |
| OUTPUTS | |||
| Main OUT | XLR | <47 ohms Balanced | 0dBu |
| Effect Send | TRS jack | 47 ohms Impedance Balanced | 0dBu |
| Link/Booth | RCA | 47 ohms | 0dBu |
| Headphones | 30-600 ohms, 75ohms recommended, Jack, Tip = left, Ring = right | ||
| 500mW RMS into 47 ohms | |||
| Mechanical Specs | Width | Height | Depth | Weight |
| Desktop | 258mm / 10.2" | 360mm / 14.2" | 90mm / 3.5" | 4.5kg / 9.9lb |
Technical Specs
Technical Specifications
OdBu = 0.775 Volts rms +4dBu = 1.23V rms
OdBu = 1 Volt rms -10dBV = 316mV rms
Maximum output level
MAIN OUT +23dBu into >2K ohm load
EFFECT SEND +21dBu into >2K ohm
LINK/BOOTH +21dBu into >2K ohm
Internal headroom
Channels +21dBu
Mix to output +23dBu
Peak indicators meters
12bar peak reading Peak on 8dB before clipping
Frequency response
20Hz-30kHz 0/-1dB
Distortion THD+noise measured at +10dBu 1kHz
0.04%
Crosstalk channel shutoff measured at 1kHz
<90dB
MIC EI Measured with 150ohm load
129dB
Residual output noise - non weighted 22Hz-22kHz filter
<88dBu
Mix noise - non weighted 22Hz-22kHz filter
<-81dBu
Power Supply Internal switch mode power unit with auto sensing mains input.
Mains In socket IEC 3 pin
AC Mains 100-240V AC 50/60Hz
Power lead Country dependent
Consumption 30W max
Fuse Rating T500mA 20mm
Internal power rails +/- 16volts
ALLEN & HEATH WARRANTY INFORMATION:
To initiate a warranty repair, you should contact Allen & Heath USA directly at 800-994-4984
RELATED ITEMS |
